discount 70% in 2018-09-24 to 2018-09-26
price: USD$ 210.00
freight :USD$7.00,(Postal parcel)
Search Similar or mail to saler or send message to saler
1. cause of the accident※Because the blade is very sharp, it is possible to touch it directly with hand.
Cleaning method▲ Use gloves and other protective appliances especially when you remove them from the casing or install them on the machine tool.
2.Cause of accident※Improper use of the method or use conditions, can lead to tool breakage flying, causing the risk of bumps.
Cleaning method▲ Please use the safety cover to protect your eyes.▲ Please use the recommended cutting conditions, and please read the instructions and sample data carefully.
3.Cause of accident※Because of the impact load and excessive wear of tools, the cutting force increases sharply, resulting in tool breakage and spatter, and the danger of damage to operators.
Cleaning method▲ Please use the safety cover to protect your eyes.▲ Please replace worn tools in time.
4.Cause of accident※High temperature chip spatter and excessive chip discharge can cause injury and scald operator.
Cleaning method▲ Please use protective gloves and other protective appliances
5.Cause of accident※The cutting process produces high temperature, so don't touch the cutting tool or workpiece directly, so as to avoid the danger of scald.
Cleaning method▲ Please use the safety cover to protect your eyes▲ When the chip is removed, the machine tool should be shut down, and gloves with pliers or clamps are used.
6.Cause of accident※The sparks produced during cutting and the sharp cutting tools that produce high temperature and high temperature chips are likely to cause fire hazards.
Cleaning method▲ The sparks produced during cutting and the sharp cutting tools that produce high temperature and high temperature chips are likely to cause fire hazards.
▲ Fireproof measures should be adopted when using non aqueous cutting fluid.
7.Cause of accident※When rotating at high speed, such as machine tool fixture and poor balance performance, vibration and chatter will occur, so that the tool broken and dangerous situation.
Cleaning method▲ Please use the safety cover to protect your eyes.▲ The machine tool must be tested, and it is confirmed that there is no vibration or flutter and other abnormal sound after the formal operation.
8.Cause of accident※Burr and other defects on the workpiece, the direct touch with the risk of injury.
Cleaning method▲ Please do not touch the workpiece with bare hands.
Cutting toolIndexableClip blade
1.Cause of accident※If the blade is not clamped with the relevant parts, the possibility of falling off or flying out in the cutting will cause injury accidents.
Cleaning method▲ Installation of the blade of the positioning surface and fastening parts, do not allow debris adhesion, should be carefully examined and believed to be reliable, and then install the blade.
▲ Please use the attached special wrench to clamp the blade and the parts, and the special wrench shall not be allowed to do other uses.
2.Cause of accident※When using the universal socket wrench and other auxiliary tools, if the clamping force is too large, it will cause micro cracks and other defects of the blade, resulting in hidden trouble.
Cleaning method▲ Only allow the special wrench to clamp the blade and other parts.
3.Cause of accident※When the tool rotates at high speed, the centrifugal force may cause the blade to fly out of danger.
Cleaning method▲ Please refer to the instructions and samples of the product and use it within the recommended range.
Various milling cuttersandOtherRotary tool
1.Cause of accident※Milling cutters can be hurt by hand touching directly with the blade.
Cleaning method▲ Please use protective gloves and other protective equipment.
2.Cause of accident※Due to eccentric rotation, unbalance and other factors, the tool causes chatter, vibration and so on. It will cause damage accidents because of the tool breakage and spatter.
Cleaning method▲ Rotation speed is selected according to the recommended conditions.
▲ In order to prevent the eccentric rotary vibration caused by bearing wear, the accuracy and balance of the rotary parts should be regularly checked.
1.Cause of accident※The rotation of the workpiece processing holes, when the drill cut left part will often fly out of the high-speed, fly out the shape of a disk and very dangerous.
Easy to cause accidents.
Cleaning method▲ Please use the safety cover, protect the eye and other protective appliances, and install the cover in the clamping part.
2.Cause of accident※The diameter of the drill bit is shaped at the top, sharp, hand contact, careless, easy to stab. Bit breakage will be difficult to remove in the workpiece,
There may be broken fly out, easy to cause injury accidents.
Cleaning method▲ Operation must pay full attention to safety, please use protective gloves, protect the eyes.
1.Cause of accident※There are razor blades falling off, crushing the risk of injury.
Cleaning method▲ Before use, make sure that the welding is reliable.▲ Please do not use it under the condition of high temperature.
1.Cause of accident※Damage to machine tools or tools is very dangerous when used except for specified use.
Cleaning method▲Please follow the prescribed method of use.