Menu

Connect with us

Gdc-j25a electromagnetic vacuum flapper valve with high vacuum flapper valve

price:USD$2769.00
discount 70% in 2018-09-18 to 2018-09-20
price: USD$ 1938.30
freight :USD$18.00,(Express)
freight :USD$7.00,(Postal parcel)
views:0
Search Similar or mail to saler or send message to saler

Pay with PayPal, PayPal Credit or any major credit card













GDC-J series electromagnetic high vacuum flapper valve is a valve which is opened or closed by electromagnetic force and spring reset force. It is suitable for opening or separating airflow in vacuum system. When the valve is closed, the upper side of the sealing surface of the valve plate is allowed to bear atmospheric pressure, and the lower side is vacuum. Under this condition, the valve plate can be opened normally after the power box is connected to the power supply.
The suitable working medium is air, non corrosive and dust free gas.

Main technical performance
 
Scope of application (Pa)
105~6.7x10-4
Valve leakage rate (Pa.L/S)
≤6.7x10-4
Applicable temperature (DEG)
-25~+40
Coil temperature rise (DEG)
≤65
Open and close time (S)
3~5
Power supply voltage (V/Hz)
220±10%/50
Installation method
vertical
 
(Figure 1) (KF) connection and outline dimensions
 
Model
Path diameter (DN)
ΦW
ΦD
ΦB
H
A
Flange standard
GDC-J16A/KF
16
68
30
17.2
186
40
GB4982
GDC-J25A/KF
25
82
40
26.2
193
50
GDC-J40/KF
40
110
55
41.2
270
65
GDC-J50A/KF
50
125
75
52.2
307
70
/
 
(Figure two) connection and outline dimensions
 
Model
Path diameter (DN)
ΦW
ΦB
H
h
bxb
n-b
Flange standard
GDC-J16A
16
68
42
165
28
48x48
4-M5
JB919
GDC-J25A
25
82
55
190
35
58x58
4-M6
GDC-J32
32
92
64
217
40
68x68
4-M6
GDC-J40
40
110
70
240
44
80x80
4-M6
GDC-J50A
50
125
90
285
56
95x95
4-M8
GDC-J65
65
135
105
315
65
115x115
4-M8
GDC-J80
80
165
125
358
75
140x140
4-M8

 

 

GDQ series pneumatic high vacuum flapper valve


GDQ series pneumatic high vacuum flapper valve (also called the angle valve) is the use of compressed air as a driving force, through the electromagnetic valve to change the direction of air passage, push the cylinder piston moves up and down, to drive the valve stem up and down movement, the valve plate is opened or closed, which can turn on or cut off the gas flow in the vacuum system to. GDQ-J type is angle pass type, GDQ-S type is three pass type with pre pumping. The suitable working medium is air and non corrosive gas.

Main technical performance
 
Scope of application (Pa)
105~1.3x10-4
Valve leakage rate (Pa.L/S)
≤1.3x10-6
Medium temperature (c)

-25 ~ +80 (sealing material is NBR)
-30 ~ +150 (sealing material is fluorine rubber)

Gas source pressure (MPa)
0.4~0.8
Installation position
DN < 300 arbitrary DN = 300 vertical
supply voltage
Standard factory: AC220V/50Hz
Special designation: AC110V; DC24V; DC12V, etc.
Signal feedback
Standard factory: without feedback signal
Special specified: magnetic switch DC/AC5 ~ 240V
 
(Figure 1) (KF) connection and outline dimensions
 
Model
Path diameter (DN)
ΦD
ΦB
H
A
Flange standard
GDQ-J10/KF
10
30
12.2
180
30
GB4982
GDQ-J16/KF
16
30
17.2
180
40
GDQ-J25/KF
25
40
26.2
200
50
GDQ-J40/KF
40
55
41.2
210
65
GDQ-J50/KF
50
75
52.2
276
70
/
 
(Figure two) looper flange connections and dimensions
 
Model
Path diameter (DN)
ΦD
ΦB
H
A
n-ΦC
DNy (pre pumping)
n-Mb
Flange standard
GDQ-J50
50
110
90
276
70
4-Φ9
/
/
GB/T6070
GDQ-J63
63
130
110
283
88
GDQ-J80
80
145
125
314
88
8-Φ9
GDQ-J100
100
165
145
338
108
GDQ-J125
125
200
175
424
128
8-Φ11
GDQ-J(S)150
150
220
195
482
138
DN40(GB4982)
JB919
GDQ-J(S)160
160
225
200
482
138
GB/T6070
GDQ-J(S)200
200
285
260
620
200
12-Φ11
DN50(GB/T6070)
GDQ-J(S)250
250
335
310
655
208
DN63(GB/T6070)
GDQ-J(S)300
300
380
350
783
250
8-Φ14
DN80(GB/T6070)
JB919
GDQ-J(S)320
320
425
395
789
250
12-Φ14
GB/T6070
GDQ-J(S)400
400
510
480
1210
330
16-Φ14
DN100(GB/T6070)
16-M12
GDQ-J(S)400
400
500
465
1210
330
8-M16
JB919
GDQ-J(S)500
500
610
580
1270
360
DN125(GB/T6070)
16-M10
GB/T6070
GDQ-J(S)600
600
710
670
1562
450
12-Φ21
DN160(GB/T6070)
12-M18
JB919
GDQ-J(S)630
630
750
720
1562
450
20-Φ14
20-M10
GB/T6070
GDQ-J(S)800
800
920
890
1900
520
24-Φ14
DN200(GB/T6070)
24-M10
Note: the dead flange n-Mb is used at the bottom of DN400.

 

 GD-J high vacuum flapper valve






GD-J series high vacuum flapper valve (also called angle valve) is used in vacuum system to cut off or connect air flow. The drive parts are driven by screw, and the lifting valve plate is light and reliable. GD-J is an angle pass type, and GD-S is a three pass type with pre pumping.
The suitable medium is air and non corrosive gas.

Main technical performance
 
Scope of application (Pa)
2x105~1.3x10-4
Valve leakage rate (Pa.L/S)
≤1.3x10-6
Medium temperature (c)

-25 ~ +80 (sealing material is NBR)
-30 ~ +150 (sealing material is fluorine rubber)

Installation position
Arbitrarily
 
(Figure 1) (KF) connection and outline dimensions
 
Model
Path diameter (DN)
ΦD
ΦB
H
A
?
ΦW
Flange standard
GD-J10/KF
10
30
12.2
122
30
?
36
GB4982
GD-J16/KF
16
30
17.2
132
40
?
36
GD-J25/KF
25
40
26.2
158
50
?
50
GD-J40/KF
40
55
41.2
180
65
?
56
GD-J50/KF
50
75
52.2
278
70
?
100
/
 
(Figure two) looper flange connections and dimensions
 
Model
Path diameter (DN)
ΦD
ΦB
H
A
ΦW
n-ΦC
DNy (pre pumping)
Flange standard
GD-J50
50
110
90
278
70
100
4-Φ9
/
GB/T6070
GD-J63
63
130
110
390
88
160
GD-J80
80
145
125
432
88
8-Φ9
GD-J100
100
165
145
460
108
GD-J(S)150
150
220
195
636
138
200
8-Φ11
DN40(GB4982)
JB919
GD-J(S)160
160
225
200
636
138
?
GB/T6070
GD-J(S)200
200
285
260
788
200
12-Φ11
DN50(GB/T6070)
GD-J(S)250
250
335
310
820
208
250
DN63(GB/T6070)
GD-J(S)300
300
380
350
980
250
8-Φ14
DN80(GB/T6070)
JB919

 

 






























Cartons, foam or wooden box packaging, Jiangsu, Zhejiang, Anhui and more express delivery, other places within 10 kg of express delivery, more than 10 kilograms of logistics (need to mention the logistics station), more than 10 kilograms of express delivery need to pay postage, if there are other problems, please contact our customer service.


Our company for general taxpayer can only open 17% VAT invoice, including tax need to above the price and then go up 17%, invoice please provide billing information.

I can't open the invoice, if available to other head Cape votes, more than 6% increase in prices, if there are other invoice please contact us.


After-sales service commitment

1. valve equipment provides free maintenance for one year and provides free spare parts list within this period. If the damage is caused by non-human cause (except for force majeure) during the maintenance period, our company will replace and repair it in time.

2. devices require life-long free repair, after the expiry of the warranty, if the buyer entrust our company to carry out maintenance, our company will maintain a replacement of equipment (ex factory price), and a detailed list of maintenance content.

3., our company in line with the interests of customers, customers want to think, anxious customers anxious, do their best to meet customer requirements, do a good job after-sales service.

Product quality commitment

1. our company introduced advanced processing testing technology from Taiwan, with superb production technology and advanced design concept of Taiwan and Taiwan to follow the ISO9001-2000 quality management system, GB, JB, SH by HG, CJ and other domestic standards and ANSI, JIS, BS, DIN and other foreign standard design and manufacture and inspection.

2. all suppliers are inspected and evaluated, and all the products are purchased only by qualified subcontractors. The raw materials, purchased parts and outsourcing parts supplied by the sub suppliers should be inspected strictly;

3. the casting and forging parts, cast steel parts and stainless steel castings provided by the sub suppliers have qualified chemical composition analysis and physical property test sheet;

4., product manufacturing strictly implement the "double three check" system, unqualified parts do not turn order, not assembled, not factory;

5. after assembly, according to GB13927, JB/T9092, CJ/T3056 standards for strength, sealing comprehensive performance test (medium for water, kerosene, gas);

6. our company responsible for the product quality and delivery time, delivery date of the warranty period of one year, life-long maintenance. For the consequences caused by product quality, our company assumes corresponding responsibility. If the consequences caused by improper operation, our company will maintain equipment at a low cost.




 

 

 

Relevant information
Welcome consultation
In the process of installing and using the user, it is unnecessary to worry about the damage of the pump due to the poor mechanical strength of the plastic. At present, the pump has obtained the national practical patent protection.
Rapid development of hot rolling H section steel production technology in China
Years ago, hot-rolled steel production in China are from diacytic type three roller rolling mill, rolling mill adopts bakelite tile bearing open or closed type frame, rolling roll changing low precision, long time, low efficiency, high energy consumption. It is precisely because there is no mill, our country can not produce economic section hot-rolled H section steel, has not yet been widely applied in china.
But in recent years, the production technology of hot rolled H section steel and profile has changed greatly in china:
The production of H type steel by rolling mill expands the production situation and application market of H steel in our country.
2, from the development of open-train mill for continuous and semi continuous rolling mill or three stand reversible, widely used in short stress or compact frame, with rolling bearing to replace bakelite tile.
3, finishing system from the past to length cooling, straightening length, to the development of large length cooling and straightening precision finishing process of long ruler.
4. From mechanical operation to automation or computer control.
H section steel is an economical section steel. It has been used in Europe and America in the early second Century. It is widely used in steel structure construction engineering. 998 years, Masteel, Laiwu Steel H steel production line has been put into production, the end of our country can not produce H steel history. At present, H steel production has been built in China in addition to Magang, Laiwu Steel, H steel, Rizhao and small Jinxi large H steel, H steel, Changzhi Laigangwanli small H steel.
These already built H type steel rolling mill adopts the international advanced technology and equipment, mainly has the following characteristics:
First, widely used blank rolling.
Two, the structure of the rolling mill has been greatly improved. In the production, the small size H section steel mill, some uses the pre-stressed high rigidity mill, the frame whole change rolls, the mill presses down is electrically driven. Some use compact frame, hydraulic press down, AGC control, when the roll, the non drive side of the frame can move, the roll system does not need to move out of the side window of the arch, can be quickly replaced.
Three is the main motor using AC variable frequency speed regulation.
Four is partial H section steel selects X-H rolling process. The rolling mill can be rolled out on the three stand reversible continuous rolling mill without rolling mill. Compared with the traditional H-H rolling technology, the finishing mill is reduced. From the actual production in foreign countries, the quality and consumption of H steel rolled by X-H method are not inferior to the traditional H-H method, and more importantly, the mill is reduced, thus reducing the construction cost.
Five is widely used long cooling, long straight straightening, cold sawing cutting ruler finishing process. The domestic new H steel is mostly finished by long cooling, long straightening and cold sawing, which reduces the blind end of the head and tail of the finished product, and improves the quality of the product. In particular, the recent construction of Laiwu Steel and Jinxi H steel, the use of double support gantry multi roller straightening machine, thus ensuring the straightening quality of large size H steel. The arch on the side of the double supporting door straightener is movable. After the arch is moved out, the manipulator hanging on the crane hangs the straightening roller at the same time, so the roll change can be realized quickly.

Mass production of new fluorine plastic alloy corrosion-resistant centrifugal pump
Jiangsu Wuxin fluorine pump manufacturing FSB fluorine plastic alloy new corrosion-resistant centrifugal pump, WIHF fluorine plastic chemical pumps and other equipment, the realization of mass production.
According to the introduction, the pump body adopts all plastic manufacturing, external metal splint reinforcement to increase its mechanical strength, change the other non-metallic pump mechanical strength difference shortcomings. In addition, there is no metal insert in the pump body, so the user needn't worry about the damage of the pump itself because of the poor mechanical strength of the plastic in the installation and use. At present, the pump has obtained the national practical patent protection.
Progress in localization of key technologies for HVDC transmission in China
The localization of the key technology of HVDC transmission in China to achieve a breakthrough: the southern power relying on Guiguang two to + 5 thousand volt DC project to achieve the goal of domestic% in the study of the system, complete design, control and protection of core technology, which has independent intellectual property and technology foundation for the large-scale HVDC project in the future, the initial change the passive situation of multinational technology, supply channels monopoly.
DC transmission has advantages over AC transmission in long distance and large capacity transmission. It has many characteristics, such as saving a large number of power transmission corridor resources, reducing electric short circuit current of load center and improving electric safety and stability level. According to the same voltage, the DC transmission efficiency is about 2 times of AC. At present, DC transmission occupies more and more share in the west to East power transmission.
According to Yuan Maozhen, chairman of the Southern Electric Power Bureau, the forecast shows that in the next 5 years, a number of DC transmission projects will be launched nationwide, and the total investment of these DC systems will be up to hundreds of billions of yuan. Due to the high technical difficulties, most of the DC transmission projects are responsible for the foreign contractors, and the key equipment and key technologies of converter transformers, converter valves, smoothing reactors and DC control protection systems have been unable to realize localization.
HVDC transmission project with 5 thousand volts and two volts is the second direct current channel of Guizhou power transmission to Guangdong province. The starting point of the project is Guizhou, Xingren. The site is located in Guangdong, Shenzhen. The total length of the line is 225 km, and the carrying capacity is bipolar 30 thousand kilowatts, which is equivalent to more than half of the load in a Western province. After the bipolar operation is put into operation at the end of 27, it can transmit 200 million kwh of electricity to Guangdong every year.
Yuan Maozhen said, two years since the start of more than years, to achieve the main, joint design, independent production, changes in the past the basic outsourcing of engineering, transnational technology monopoly situation, the overall realization of 7% (according to the value of the project) independent goal requirements. System research, complete set design, DC control protection equipment% completed by China, converter valve completed by the Chinese side, station commissioning and system commissioning% completed by china. The converter transformer 57% is made by the Chinese side, and the flat wave reactor 67% is made by the Chinese side, and the thyristor 75% is supplied by the Chinese side.
In the two dynasties of Guangdong and Guangdong, we adopted the effective organization mode of "I as the main", and introduced and digested the strategy of introducing and digesting by the Chinese side, which successfully realized the localization, introduction, digestion and innovation. The "Southern Power Project" management, Design Institute, XJ Group and other domestic direct design and manufacture of the backbone of organized, centralized, joint research, the key technology breakthroughs in autonomy. In order to ensure Mastery